• The machine does not start • Load of water does not stop in... • The tank is not filled or the rinse... • Water is not heated • The tank does not empty • The dishwasher does not wash... • Glasses and dishes are not... • Condensate on glasses • "Bloom" on glasses • Too much foam in the tank • "Striated or spotted" glasses • Wash/rinse arm do not turn... • The rinse aid injector does not... • Water level is higher than...   The machine does not start 1) CHECK THAT THE BUILT-IN WALL SWITCH IS CORRECTLY PROVIDED WITH VOLTAGE 2) CHECK THAT THE MAIN SWITCH (0-1) IS CORRECTLY PROVIDED WITH VOLTAGE 3) CHECK THAT THE DOOR IS PERFECTLY CLOSED AND THAT THE MICRO- SWITCH IS OPERATING 4) CHECK THAT THE TANK WATER LEVEL PRESSURE SWITCH IS WORKING, ALSO THE SOLENOID VALVE Load of water does not stop in the tank 1) CHECK THE EFFICENCY AND CALIBRATION OF THE PRESSURE LEVEL IN THE TANK The tank is not filled or the rinse is not operating 1) CHECK THAT THE TANK WATER LEVEL PRESSURE SWITCH IS WORKING AND THAT IS PROPERLY ADJUSTED 2) CHECK THAT THE INLET TAP IS CORRECTLY OPENED 3) CHECK THAT THE MAIN SWITCH IS ON THE "1" POSITION 4) CHECK THAT THE NETWORK SWITCH IS ON THE "ON" POSITION 5) CHECK THE MAIN SWITCH CONNECTIONS AND FUSES 6) CHECK THAT THE WATER WASH ARMS AND JETS ARE NOT CLOGGED BY LIMESCALE OR SOLID WASTES 7) CHECK THERE IS NO WATER IN THE AIR BOX. REMOVE THE DRAIN PLUG AND COMPLETELY EMPTY THE TANK. IF THE DEFECT REMAINS REPLACE THE PRESSURE SWITCH 8) CHECK THAT THE INLET SOLENOID VALVE IS CORRECTLY WORKING. IN CASE OF FAULTY ACTIONS REPLACE IT Water is not heated 1) LET WATER ENTER THE TANK WHILE CHECKING THAT THE DRAIN PLUG IS CORRECTLY POSITIONED 2) CHECK THAT THE THERMOSTATS OF THE HEATING ELEMENTS ARE CORRECTLY WORKING. IF THEY ARE NOT, REPLACE THEM 3) CHECK THE ELECTRIC ELEMENTS The tank does not empty 1) THE DRAIN PIPES IS POSSIBLY CLOGGED BY SOLID WASTES. REMOVE IT FROM THE DRAIN PIPE OR POSSIBLY REPLACE THE PIPE The dishwasher does not wash properly 1) IF THE SUCTION FILTER IS CLOGGED, CAREFULLY CLEAN IT 2) CHECK THAT THE WASH ARMS AND JETS ARE NOT CLOGGED BY SOLID WASTES 3) CHECK THAT THE INITIAL DETERGENT QUANTITY AND THE CYCLE DOSES ARE CORRECT 4) THE CHOSEN WASHING CYCLE IS TOO SHORT SHIFT TO A LONGER CYCLE OR REPEAT THE CHOSEN CYCLE 5) CHECK THAT THE WASHING WATER IS SUFFICIENTLY HOT Glasses and dishes are not properly dried 1) CHECK INSTRUCTION RELATING TO THE RINSE AID INJECTOR 2) CHECK THE QUALITY OF THE RINSE AID LIQUID Condensate on glasses 1) GLASSES ARE NOT CORRECTLY POSITIONED 2) WRONG RINSE AID DOSAGE 3) WRONG DETERGENT DOSAGE "Bloom" on glasses 1) ONLY USE PRODUCTS WHICH DO NOT PRODUCE FOAM AND WHICH ARE SUITABLE FOR PROFESSIONAL DISHWASHER Too much foam in the tank 1) CHECK THAT WATER TEMPERATURE IN THE TANK IS NOT LOWER THAN 50°C 2) CHECK THE RINSE AID INJECTOR EXCESSIVE DOSE 3) CHECK THAT THE TANK WAS CLEANED WITH SUITABLE DETERGENT. EMPTY AND THOROUGHLY RINSE SEVERAL TIMES BEFORE STARTING A NEW CYCLE 4) SHOULD A FOAMY DETERGENT BE WRONGLY USED, EMPTY AND RE-FILL THE TANK WITH WATER UNTIL FOAM DISAPPEARS "Striated or spotted" glasses 1) REDUCE THE RINSE AID QUANTITY FOR EACH CYCLE SUGGESTED DOSE: 0,1 c.c. PER LITER OF WATER Wash/rinse arm do not turn correctly 1) DISASSEMBLE THE ARMS AND JETS AND CAREFULLY CLEAN THEM 2) CHECK THAT THE INLET PRESSURE IS HIGHER THAN 200 kPa (2 bar). SHOULD IT BE LOWER, USE A PUMP WHICH INCREASES PRESSURE The rinse aid injector does not work 1) CHECK THE INJECTOR CONTAINER, IF IT'S EMPTY, FILL IT UP AND CONNECT IT ONCE MORE Water level is higher than drain-plug 1) CHECK IF OUTLET PIPE IS CLOGGED